lasasturtle.blogg.se - Brocade san switch snmp configuration cli

#BROCADE SAN SWITCH SNMP CONFIGURATION CLI HOW TO#
#BROCADE SAN SWITCH SNMP CONFIGURATION CLI PASSWORD#
#BROCADE SAN SWITCH SNMP CONFIGURATION CLI SERIES#

The following example shows how to display all aliases: If name is not specified, all defined aliases are displayed. (Optional) Name of the alias to be displayed. Use the show alias command to display a listing of defined command aliases.

show commands are described in the " ATM show Commands" chapter show alias.

General commands are described in the " General ATM Commands" chapter.

set commands are described in the " Switch set Commands" chapter.

clear commands are described in the " Switch clear Commands" chapter.

General commands are described in the " General Switch Commands" chapter.

Other commands are described elsewhere in this publication: For more information about using the switch CLI, refer to the " Switch Command-Line Interface" chapter. For a summary of the available switch CLI commands, refer to the " Switch Command Quick Reference" chapter.

#BROCADE SAN SWITCH SNMP CONFIGURATION CLI SERIES#

And then enable the configuration by cfgenableīut if you are creating a zone for the first time in a switch, you would have to create a configuration file before running cfgsave.This chapter describes the show commands used in the Catalyst 5000 series switch command-line interface (CLI). save the configuratiuon after creating the zone bye cfgsaveĨ. Now create the zone ( zonecreate “TRAINING_hba1_SPA_A0”, “TRAINING_hba1 SPA_A0” )ħ. Now create aliases for clarion if not created before and this will be constant throughout ( alicreate “SPA_A0”, “wwn of storage” )Ħ. Now create aliases for server ( alicreate “TRAINING_hba1”, “wwn of hba1” )ĥ. login to the switch and match the wwn, run switchshow command.Ĥ. of HBA card ( for solaris – fcinfo & HP-UX – fcutil)ģ. login into the server and find the wwn no. Connect the cable to switch (LC to LC) from server HBA port to one of the switch port.Ģ. just for eg and to understand the nomenclature, when you work independently.ġ. Now assume you have a server named “TRAINING” with two HBA hba1 and hba2 and a storage clarion with FE ports A0. Zoning Commands ( Preferably do it GUI unless so sure to do it CLI)īefore knowing the commands, keep in mind the storage (clarion), servers(to be zoned), switch (on which to do the zoning), every details. These are some of the basic commands for brocade switches, most of them, you wont be using much, Lot many have complete description behind them which can not be explained over here. agtcfgset – to configure snmp to send switch alerts to particular server.

agtcfgshow – to check is snmp is configured or not.ģ0. configupload – to take backup of switch configuration, very important.Ģ9. nscamshow – shows what exactly is there in cache that has not been saved yet in memory.Ģ8. portcfgshow – to check the port speed, configuration.Ģ7. Where can be 0 : autonegotiated, 1 : 1Gbit/sec, 2 : 2Gbit/sec.Ģ5.

portcfgspeed, - to configure speed of particular port.Ģ4. portperfshow – to check performance of each switch port.Ģ3. portshow – displays status of all ports.Ģ2. portdisable & portenable, these can be used as a part of troubleshooting, say is HBA is connected to a particular switch port but it is not detecting, then you can try out disabling and enabling the switch port.Ģ1. switchstatusshow – displays overall status of the switch.Ģ0. tstimezone – for changing the timezone.ġ9. If time changes say ( day light savings), it would be difficult to change the time manually for each switch but change can be replicated to each switch by above command if there would be and NTP server configured.ġ8. It is very important to set the exact time (can’t explain here)and also it has a significance for environment having lot many switches. tsclockserver “IP of NTP server” – will synchronise the time as what is there in NTP server. switchname “newname” –to change the name of the switch.ġ6. switchname – displays the name of the switch.ġ5. userconfig -delete username – to delete the account for particular user.ġ4.

#BROCADE SAN SWITCH SNMP CONFIGURATION CLI PASSWORD#

passwd username – to change the password for particular user.ġ3. userconfig -add username –r rolename – to create an account for particular user and rolename will define the previlleges eg admin, switchadmin, zoneadmin etc.ġ2. userconfig -show –a – will show all accounts in a switch.ġ1. fabricprincipal –f 1 – to make a particular switch as primary switch.ġ0.

and 00 is fabric service (ALPA address).ĩ. Eg o/p would be (010000) where 01 is switch domain ID, 00 is port no. nsallshow – shows all name databases details i.e how many servers are connected and to which port. switchshow – gives WWN of switch and ports.Ĩ. version – gives version of fabric operating system.ĥ. Check on the case sensitivity using command “help” ( it will demonstrate all the possible commands)ġ.